How do I make a Hell in a Cell?
You will need…
-About 15 steel dowels
-Hardware cloth(chicken wire, only square)
-Soddering Iron(Hobby Shop)
-19 guage wire
1.) First, take the dowels and make them into a square shape |_| four times. Using the Soddering Iron, put them together into a cube shape so it is like a box. The actual size depends on the ring you are using. When measured out, there should be 4" between the side of the cell and the ring. Only put 3 of the sides together for now.
2.) Get the Hardware cloth, and sodder it onto each side. Cut off different pieces for each side. DON'T WRAP IT AROUND. Go ahead and put it on the 4th side as well.
3.) Take some more dowels, and sodder them ontop of the caging so that the cage is between the frame and the supporting beams. Attach them so they make a -|-|-|- shape. the underline being the bottom of the cage, and the dashes and vertical lines behind the supporting beams. Do this for each side. DO NOT DO THIS FOR THE TOP!
4.) Using the little hinges, Sodder them every 5" along the top of the 4th side. Being very careful, sodder the other end of the hinge to the cage itelf. You are now able to move the cage side up and down(Don't try to attempt until Metal is cooled and stable).
5.)Now comes the top of the cage. Look at the sides of the cage, and measure out pieces of dowel that will connect the opposite ends of each dowel so that it appears to have a connecting pipe from one side to the other. When completed, the top should look like a giant Tic-Tac-Toe board(with one added line in each direction).
6.) Now come the main supports on the top. Find the very center of the top of the cage, add put a 2" long piece of dowel vertically(sticking up). Measure from the middle of each side to the center stake. Cut pieces that long, and then sodder them to the center stake and center of each pipe /|\.
7.) The door- To make the door, find a point anywhere on the side of the cell, and cut it out. To get the correct height, measure out the size of a TTL Big Show figure. If he can fit through, any figure can. Surround the sides of the piece with the dowels, and then surround the outside of the hole with dowels to. That makes the door, and the door frame. Using the hinges like before, affix the door. For added looks, you can add the chain that comes with the TTL 7 Undertaker.
8.) The hole- To make the hole, do exactly as the door, only put it on the top of the cell(duh!). It works best if put next to one of the supports, and the hinge is hidden from plain sight. Put a small piece of double-sided tape on the side opposite the hinges, and it will stay closed until needed.
NOTE- Steel Dowels can be replaced with Wooden Dowels. They are cheaper, but don't look near as well. If you use the steel, you don't need spraypaint. The soddering Iron can be replaced with hot glue, but again, doesn't look as good.
I am not entirely sure, but I may be thinking about a small welding iron instead of a soddering iron. You may want to look into that before buying one.How do i make weapons?
take some little ties from wwe packages(usaly comes in boxed sets but my draft Rock had some to) and take a wCw or ECW baseball bat and wrap the ties around
Singapore canes: you need 6 toothpicks, glue 3 of the ends (of 3 toothpicks) together in a triangle. Do this again and then place the two unglued sides together and voila
Some Deathmatch Ideas are-
Barbwire TLC - Name Explains
Flaming Tables - Name Explains
Fans Bring the Weapons Match - Just have your fans or whatever you use bring various weapons
Lumberjack Lighttube- Basic Lumberjack match only Lumberjacks have Light Tubes
Log Cabin of Glass Deathmatch- Lightubes in a giant square. 3 or 4 Cabins in a match
Circus Deathmatch - Barbwire Net across the ropes and a giant scaffold over or near the ring. Done in Japan with Matsunaga and In the U.S. with MadMan Pondo and J.C. Bailey on the 2nd Night of Ultra Styles Clash
Click the link below for a picture of the set up.circusdeath.iwamidsouthwrestling.com
Caribbean Spider Web- Barbwire on Ropes shaped like X on 2 sides of the ring and Rubbing Alcohol pit on one side and whatever on the other.
Cactus Death Match.
(For more Information on the Circus Death Match at the IWA Midsouth, go to www.iwamidsouthwrestling.com
or order the tape on www.smartmarkvideo.com
. The Name of the tape is Ultra Styles Clash and it is a two tape set with Ace Steel vs. A.J. Styles on the First Night and A.J. Styles vs. Colt Cabana and the Circus Deathmatch on the 2nd night)
Tables- To make a table (these can be really awesome) you cut a rectangle out of a piece of cardboard of whatever size of the table you want. You then cut it in half so there are two squares. You then set them the way they were before they were cut inhalf and STRONGLY tape 2-3 toothpicks over the broken parts to stick them back together. For legs you use straws and tape them whatever way u can to keep them on. (In addition u can cut the table whatever way u want and then use several more toothpicks to keep them together)
Ladders- Cut out two rectangles of large sizes (the sizes of 1 of the sides of the ladder u want) then tape the top two pieces together tightly and use a magic marker to color the cardboard to make it a ladder.
Glass I use the CD Gem Case's and smash them up!
Blood The fake blood from halloween works and it come's off easily or ketchup.Rey Spring Board Launcher
You will need
x20 popsicle sticks
x9 mechanicle pencils.ather up the springs.
3. Glue 8 springs around the perimiter of one of the bases. Then place the last one in the middle
000 = (Springs in shape of square)
4. Glue other base on top.
Put Rey on it, press down and he should jump fairly goodHow can I make a custom ring?
20"x20" particle board, 3/4" thick
4 1/2" Dowels (10" long)
16 small hook screws
328" elastic string
20 sq. in. Cloth
1. Put the cloth on the board, and Trace a circle using the dowels in the corners of the ring, about 1/2" away from the actual cut corner.
2. Drill out the circles, with the cloth intact.
3. Stick the dowels into the holes, 5 1/4" on top, 4" onthe bottom.
4. Staple the cloth into place.
5. Drill the tiny hooks into the dowels
6. Cut the elastic string into 4 82" pieces.
7. run the string under the hooks. You will have 2 extra inches to tie.
8. You will now have a prototype for your ring
9. Use foamies to create pads in the corner.
10. Make some aprons, and you're finished