Deleted
Joined on: Sept 22, 2024 6:33:38 GMT -5
Posts: 0
|
Post by Deleted on Nov 24, 2013 11:02:27 GMT -5
I am trying to swap the head from Basic 31 ADR to an older basic ADR figure. The older figure is with his grey attire and smiling headscam (I'm not sure what it is from- got at flea market). Any way the b31 head fit fine on the older body with the grey entire, but the older head won't fit right on the B31 body. Anyone run into this problem before when head swapping? Any ideas, guidance, solutions? Used boiling water to do head swap.
|
|
Deleted
Joined on: Sept 22, 2024 6:33:38 GMT -5
Posts: 0
|
Post by Deleted on Nov 24, 2013 11:04:21 GMT -5
Reheat the Peg in the Headless body, and Pour water into the other ADR Head. This should work
|
|
|
|
Post by SuperJimmy12345 on Nov 24, 2013 12:04:49 GMT -5
I had this with old Ortons,one of the pegs is bigger. Try a hairdryer instead of water.
|
|
|
|
Post by marino13 on Nov 24, 2013 12:53:53 GMT -5
I've swapped B31 Del Rio's head a couple times and never had a problem. Never had a problem putting the old one on the B31 body either. Did you try hot water?
|
|
Deleted
Joined on: Sept 22, 2024 6:33:38 GMT -5
Posts: 0
|
Post by Deleted on Nov 24, 2013 16:00:10 GMT -5
The head goes on, but not all the way. It fits on there like a bobble head.
|
|
Deleted
Joined on: Sept 22, 2024 6:33:38 GMT -5
Posts: 0
|
Post by Deleted on Nov 24, 2013 16:20:45 GMT -5
The head goes on, but not all the way. It fits on there like a bobble head. Give it a piledriver. Should pop on then. |
|
n2jib
Main Eventer
Joined on: Mar 2, 2012 11:01:59 GMT -5
Posts: 1,546
|
Post by n2jib on Nov 24, 2013 18:38:17 GMT -5
U would need to deepen the peghole i guess?
|
|
Deleted
Joined on: Sept 22, 2024 6:33:38 GMT -5
Posts: 0
|
Post by Deleted on Nov 24, 2013 19:06:59 GMT -5
Try pushing it on harder. Sometimes they look like they are on, but they Arnt all the way in.
|
|
Deleted
Joined on: Sept 22, 2024 6:33:38 GMT -5
Posts: 0
|
Post by Deleted on Dec 25, 2013 20:37:50 GMT -5
I am trying to swap the head from Basic 31 ADR to an older basic ADR figure. The older figure is with his grey attire and smiling headscam (I'm not sure what it is from- got at flea market). Any way the b31 head fit fine on the older body with the grey entire, but the older head won't fit right on the B31 body. Anyone run into this problem before when head swapping? Any ideas, guidance, solutions? Used boiling water to do head swap. I was never able to get the ADR head on correctly. Most of head swaps work out just fine, but I ran into a problem on another swap. Trying to swap heads between COO Triple h and TRU exclusive Triple H. The head from the exclusive went onto to the COO body just fine, but I can't get the COO head onto the exclusive to fit down correctly. It will go of the peg but sits like a bobble head. I tried giving it a "pile driver" but it just seems it won't fit down on the peg correctly. Help please! |
|
|
|
Post by CMPUNKISGOOD on Dec 25, 2013 20:50:23 GMT -5
The COO HHH has a short neck which makes it a bobble head
|
|
|
|
Post by Joe/Smurf on Dec 25, 2013 21:19:28 GMT -5
U would need to deepen the peghole i guess? That's what... she said? |
|
|
|
Post by The Mask of Truth on Dec 25, 2013 22:09:50 GMT -5
I think the neck is thicker on the newer Del Rio figures.
|
|
