|
|
Post by bigchrisfilm on Jul 16, 2006 2:20:49 GMT -5
How can I remove a DA head, and put it on a RA body? Thanks.
|
|
|
|
Post by Ministry of Darkness on Jul 16, 2006 3:02:42 GMT -5
Custom support centre!
|
|
|
|
Post by Magneticman, Remember? on Jul 16, 2006 3:29:29 GMT -5
Yeah wrong place..but to answer your question put your or a flat head screw driver under the head or put your thumb under the head and just push it.
|
|
|
|
Post by PJ on Jul 16, 2006 4:38:15 GMT -5
Heat the head with a hair dryer for about a minute. Then sqeeze the neck very firmly and push up the chin until the head pops off. If you squeez the neck hard enough the post/stem will stay in the neck and not come out in the head.
PJ
|
|
|
|
Post by STOMWIJF on Jul 16, 2006 6:00:49 GMT -5
Stick the figure in warm water for a minute and just pop the head right off with your thumbs.
Don't use screwdrivers or hair dryers.... they leave marks.
|
|
|
|
Post by PJ on Jul 16, 2006 6:04:52 GMT -5
Stick the figure in warm water for a minute and just pop the head right off with your thumbs. Don't use screwdrivers or hair dryers.... they leave marks. Heating it with a hair dryer has never left a mark for me, but I have had figures skin tone fade in hot water. PJ |
|
|
|
Post by BigDaddyChacon on Jul 16, 2006 10:11:34 GMT -5
I just grab the head from undeneath the chin and pull up. The head pops right off.
|
|
|
|
Post by Snitch on Jul 16, 2006 10:15:59 GMT -5
While we're on the subject of sticking a figures head in water, do they have metal parts in because my dad said i couldn't put a figure in water because the metal parts inside will rust.
|
|
W¡LDCARD
POSSIBLE BAD TRADER
Sell me your TNA figures!
Joined on: Mar 23, 2005 3:32:51 GMT -5
Posts: 3,444
|
Post by W¡LDCARD on Jul 16, 2006 10:18:28 GMT -5
Nope, they don't. It's all plastic (or whatever material Jakks makes their figs out of).
|
|
|
|
Post by Snitch on Jul 16, 2006 10:19:37 GMT -5
Thanks  |
|
|
|
Post by STOMWIJF on Jul 16, 2006 10:45:18 GMT -5
Stick the figure in warm water for a minute and just pop the head right off with your thumbs. Don't use screwdrivers or hair dryers.... they leave marks. Heating it with a hair dryer has never left a mark for me, but I have had figures skin tone fade in hot water. PJ In all honesty.... I let the wind dry my hair ;D, but I suppose you should have taken the figures out off the hot water sooner. |
|
|
|
Post by takerrules on Jul 16, 2006 10:49:15 GMT -5
With a guillotine. It's a tad barbaric, and outdated, but you can also use a sword. I'd be careful if I were you, everything youve seen on CSI is real and they'll probally catch you. lol.
|
|
|
|
Post by reecechillin on Jul 16, 2006 12:48:24 GMT -5
^^^ lol ^^^ i tried that once ^^^
|
|
|
|
Post by cenasfan on Jul 16, 2006 13:16:26 GMT -5
pop it off ?
|
|
Hbk1994
Superstar
Joined on: May 25, 2006 2:20:26 GMT -5
Posts: 778
|
Post by Hbk1994 on Jul 17, 2006 6:45:59 GMT -5
CUSTOM SUPPORT CENTRE IS MY ANSWER
|
|
Deleted
Joined on: Nov 24, 2024 22:59:29 GMT -5
Posts: 0
|
Post by Deleted on Jul 17, 2006 21:17:40 GMT -5
Yikes. A hella lot of threads asking about removing heads and such. Here's a reply from another thread I left: Use a hairdryer. On high heat, heat the head all the way around (gotta keep rotating or it won't heat all the way through). When it gets softer (usually after a minute), it's ready to be pulled off. Gently pull off. Much cleaner and better than water. Water can discolor the figure. To get the head to harden back, stick it in the freezer for about a minute; remove. Let sit for another minute to thaw. After that, it'll be good as new. |
|
