|
|
Post by ayoterror1rcwcorp on Feb 20, 2008 12:14:50 GMT -5
Rhyno!  Still need to paint it Before  Before (Front)  Before (Back AFTER (part 1)   Tell me What you think So far plz! |
|
Deleted
Joined on: Dec 4, 2024 14:50:25 GMT -5
Posts: 0
|
Post by Deleted on Feb 20, 2008 12:31:04 GMT -5
Protos go in the customs disscussion thread.
|
|
|
|
Post by guygardner on Feb 20, 2008 12:37:06 GMT -5
Super heat the neck joint on the body with a blow dryer. That will loosen up the plastic enough where you can use a pair of needle-nosed pliers to pull the ball out of the torso.
|
|
|
|
Post by ayoterror1rcwcorp on Feb 20, 2008 12:43:50 GMT -5
Thanks!
|
|
|
|
Post by alex123ecw on Feb 20, 2008 13:02:12 GMT -5
Take some pliers and grab the on i nthe body and just bend back, it'll pop right out, that heating crapcan melt your figs.
|
|
|
|
Post by guygardner on Feb 20, 2008 13:05:10 GMT -5
Take some pliers and grab the on i nthe body and just bend back, it'll pop right out, that heating **** can melt your figs. Without heating the joint you run the risk of breaking off a piece of the joint collar. Heating with a blow dryer won't melt the figure unless you place it directly on the plastic, which quite frankly only an idiot would do. |
|
|
|
Post by f1gh7er on Feb 20, 2008 13:18:30 GMT -5
warm it with hot water and take some plaiers and yank it out like everybody else and use testors acrilic paint (avable at hobby lobby for 2 sumthing for lil thing of it but it lasts a wile)
|
|
|
|
Post by alex123ecw on Feb 20, 2008 13:19:11 GMT -5
I've never broken a collar piece, or melted the plastic, I'm just saying you could.
|
|
Dyamez
Main Eventer
Joined on: Aug 24, 2006 14:30:15 GMT -5
Posts: 1,394
|
Post by Dyamez on Feb 20, 2008 13:33:01 GMT -5
i use boiled water. or better yet, just take out the one that is connected to the body. It is easier to remove
|
|
|
|
Post by ayoterror1rcwcorp on Feb 20, 2008 13:33:55 GMT -5
Alright, Thanks Guys!
|
|
|
|
Post by alex123ecw on Feb 20, 2008 13:58:36 GMT -5
i use boiled water. or better yet, just take out the one that is connected to the body. It is easier to removeexactly |
|
|
|
Post by The Assassin on Feb 20, 2008 15:58:16 GMT -5
boil up some water in a kettle, pour it into a cup or a pan, hold the head in it for a few minutes with some pliers or something
then use some small pliers to pull out the peg
|
|
|
|
Post by The Dude on Feb 20, 2008 17:49:18 GMT -5
Take some pliers and grab the on i nthe body and just bend back, it'll pop right out, that heating **** can melt your figs. Heating doesn't melt your figures, unless you are a complete idiot and don't know how to do it. Boiling your figures can ruin them easier than blow drying. |
|
|
|
Post by ayoterror1rcwcorp on Feb 21, 2008 14:58:36 GMT -5
Updated! |
|
|
|
Post by tempts4lifer on Feb 21, 2008 17:26:00 GMT -5
this still belongs in custom disscussion. its a wip.
|
|
